Plane 1 - Type: Profile Plane
Weight: 115, Length: 131, Width: 15, Height: 120, Min Height: 60.
Right side 3.3 cm flat, widened by 0.4 cm, and 2.3 cm flat downward with shaving hole.
Left side 5.9 cm flat and small 0.4 cm bevel to the left side stop.
Left stop 0.5 cm, right stop 0.7 cm, positioned at a right angle to each other.
The plane should be held at an angle to the wood.
Right at 20° or left at 70°. It cuts a profile on the wood edge.

Blade: 8 mm
Shaft: 5 mm
Cutting angle: 56°

Plane 2 - Type: Profile Plane
Weight: 130, Length: 130, Width: 18, Height: 110, Min Height: 59.
Top edges chamfered, wooden wedge.
Right side 3.1 cm flat, widened by 0.6 cm, and 2.4 cm tapering down by 0.3 cm, with shaving hole.
Left side 5.9 cm flat and small 0.3 cm bevel to the left side stop.
Left stop 0.2 cm, right stop 0.5 cm, as with the predecessor but should be held at 10° to the right and 80° to the left.

Blade: 10 mm
Shaft end: 4.5 mm
Cutting angle: 57°

Plane 3 - Type: Profile Plane
Weight: 135, Length: 131, Width: 21, Height: 115, Min Height: 58.
Top edges chamfered, wooden wedge.
Right side 2.9 cm flat, widened by 0.5 cm, and 2.7 cm flat downward with shaving hole.
Left side 5.8 cm flat and 0.3 cm bevel to the left side stop.
Left stop 0.2 cm, right stop 0.9 cm, positioned at a right angle to each other.
The plane should be held at an angle to the wood.
Right at 20° or left at 70°. It cuts a profile on the wood edge.

Blade: 9 mm
Shaft: 5 mm
Cutting angle: 57°

Plane 4 - Type: Groove Plane
Weight: 65, Length: 132, Width: 12, Height: 80, Min Height: 45.
Top edges chamfered, two wooden wedges attached to the right.
Right side 4.5 cm high, with notches for the blade and wedge.
Small shaving hole below.
Left side 4 cm high.
Lower depth stop 0.8 cm wide.
Depth stop 0.5 cm. No side stop.
Nail holes for temporary stops.

Blade: 4.5 mm
Cutting angle: 55°
Pre-cutter: 4.5 mm
Cutting angle: 90°

Plane 5 - Type: Ship Sash Plane
Weight: 80, Length: 103, Width: 15, Height: 90, Min Height: 50.
Radius approximately 18 cm.
Top edges rounded, wooden wedge.
Both sides flat.
Continuous shaving hole.

Blade: 15 mm
Shaft: 6 mm
Cutting angle: 55°

Plane 6 - Type: Groove Plane
Weight: 290, Length: 130, Width: 35, Height: 140, Min Height: 97.
. Top edges rounded, wooden wedge attached to the right.
Bronze oval cap screw 70 mm, head 21x6 mm, 24 mm long.
Inset bronze plate 42x12 mm with retaining notch and two screws.
Right side 6 cm flat with cone recess for blade and wedge, shaving hole below.
Left side 2.8 cm flat, then 1.4 cm wider, 2.2 cm flat.
Sole from 3 cm horizontally to 0.6 cm wider, 0.9 cm deeper 6 mm groove.
Depth adjuster bronze plate 45x12 mm beneath the bronze adjusting screw.
Depth range 1–9 mm.
Side stop 13x2.1x1.9 cm wood with two notches (15x5 mm), 19x10 mm bronze inserts for wood screws.
Stop width 0.4 mm, depth 1.3 cm.

Blade: 6 mm
Cutting angle: 53°

(5 profile samples included)
(Weight and measures below from plane 1).